Asus laptop motherboard schematics
- #ASUS LAPTOP MOTHERBOARD SCHEMATICS HOW TO#
- #ASUS LAPTOP MOTHERBOARD SCHEMATICS DRIVER#
- #ASUS LAPTOP MOTHERBOARD SCHEMATICS MANUAL#
- #ASUS LAPTOP MOTHERBOARD SCHEMATICS UPGRADE#
- #ASUS LAPTOP MOTHERBOARD SCHEMATICS PC#
#ASUS LAPTOP MOTHERBOARD SCHEMATICS MANUAL#
1005HA is a Linux hardware manual online.ġ3-03-2010 Hello, Thank you for reading this thread. 05-01-2010 I have a 1005HA EEE pc, and I have everything up and working perfectly, except the mic at least in regards to skype which is the only place I need and/or use it. A-8 Nordic Lithium Cautions for lithium-ion. At the time of its introduction in late 2007, it was noted for its combination of a lightweight, Linux-based operating system, solid-state drive SSD, and relatively low cost.
#ASUS LAPTOP MOTHERBOARD SCHEMATICS DRIVER#
RPMFusion has a kmod package with this driver kmod-rt2860.
#ASUS LAPTOP MOTHERBOARD SCHEMATICS PC#
The touchpad, on the other hand, is removable.900 XP Model, Somehow the BIOS does not find the image on my Eee PC 900. In a case of keyboard failure I suggest you replace the entire top case. It’s possible to replace the keyboard without replacing the top case but it’s not easy. The keyboard is permanently attached to the top case. If the DC jack fails, it has to be de-soldered from the board and replaced with a new one. The DC power jack is soldered to the motherboard. Here’s the other side of the motherboard. Lift up the optical drive and hard drive connector board to disconnect it from the motherboard and remove it.ĭisconnect the keyboard cable (red) and the touchpad cable (yellow) from the motherboard.īoth connectors have to be unlocked before you disconnect the cable. Remove two screws securing the optical drive and hard drive connector board. The display panel has to be removed in order to replace the screen.
#ASUS LAPTOP MOTHERBOARD SCHEMATICS HOW TO#
In the next guide I explain how to take apart the display panel and remove the LCD screen. Separate the display panel from the top case assembly. Remove four screws securing the display panel hinges. Open up the display panel 90 degrees and place the laptop upside down on the edge of the desk as it shown on the following picture. Lift up clear tape securing the connection and pull the display cable out. The connector looks fragile with a bunch or thin wires exposed. In order to disconnect the wireless card antenna cable simply lift up the cable “head” and un-snap it from the connector on the card.īe careful while disconnecting the display video cable. Disconnect the display video cable from the motherboard (yellow). Display panel removalĭisconnect one antenna cable from the wireless card (red). Disconnect the fan cable from the motherboard.Ĭarefully separate the heatsink from the processor and remove the fan assembly. Remove seven screws securing the cooling fan assembly (fan and heatsink). Remove one screw securing the optical CD/DVD drive. The bracket is secured by four screws (two on each side).
#ASUS LAPTOP MOTHERBOARD SCHEMATICS UPGRADE#
If you decide to upgrade to a solid state drive, you’ll have to transfer the mounting bracket to the new drive. I would strongly recommend upgrading it to a 2.5″ solid state drive which will make your laptop much faster. Lift up the left side of the hard drive and pull it away from the motherboard to disconnect from the SATA port.Īsus F556U series laptop has a regular 2.5″ spinning (slow) hard drive installed. Remove two screws securing the hard drive bracket. Lift up and remove the I/O board (USB/audio jack/card reader) with the cable attached. Release the latch to separate the board from the top case.
There are no screws securing the board but there is a small latch on the right side. Lift up the locking tab (red arrow) to unlock the connector and pull the cable out. It’s necessary to remove the I/O board with the cable in order to remove the hard drive.ĭisconnect the I/O cable from the motherboard. The hard drive is mounted under the I/O board cable and part of the hard drive bracket is located under the I/O board.
Remove two screws attaching the battery to the top case. You’ll have to use some reasonable force to remove the cover. There are many hidden latches securing the base cover. Move the spudger along the side and try up the base cover.Ĭontinue removing the base cover with your hands. Start separating the base cover from the top case using a plastic spudger. Using a small screwdriver make holes for the screws and secure all screws on the diagram. Draw a diagram of all bottom screw locations on a piece of paper. Keep track of all removed screws, it will help a lot during the re-assembly process. For some reason Asus decided to use five different types of screws on the bottom.